How to: Remove & Install A Truck Hub Bearing Assembly with Timken
Watch the experts at Timken remove and install a truck hub bearing assembly on a GM 4x4 front wheel with outboard mounted rotors. The experts will show you how to remove a hub assembly and then show you how to install a hub assembly.
For more tech tips from Timken experts, visit http://bit.ly/eHcVvw.
2000 Honda Civic Si 1.6L Clutch Install
This video is a 2000 Honda Civic Si 1.6L clutch installation with Gary Croyle. The clutch set used was a part number MU70137-1 (Brute# 92329). An image of the clutch set can be found at the following link: http://perfectionclutch.com/applookuptest/images/MU70137-1-1.jpg
---------------------------
The clutch diameter and dimensions are as follows:
8-5/8" Diameter x 24 Teeth x 1-1/32" Hub
----------------
This clutch set fits the following vehicles:
ACURA INTEGRA GSR L4 1.8L GAS N 1997-01
HONDA CIVIC DEL SOL VTEC L4 1.6L GAS N 1994-95
CIVIC SI L4 1.6L GAS N 1999-00
CR-V EX L4 2.0L GAS N 1998-01
CR-V LX L4 2.0L GAS N 1997-01
CR-V SE L4 2.0L GAS N 2000-01
2003 Mazda Front Wheel Bearing Replacement (Press In Type Bearing)
Wheel bearing replacement in a 2003 Mazda Protege 5. Press in style bearings done without using a shop press. Specific for Mazda Protege, but many of the techniques will apply to vehicles with pres-in-style wheel bearings.
It's a good idea to try to use the bearing-press-kit the way it was intended. If the bearing doesn't budge, BE CAREFUL using a breaker bar. The bolt supplied with the press-kit is not very strong...it with probably shear off the head. Try to give the bearin a few hits with a sledge hammer as seen in the vid..it will get the bearing moving. Then you can use the press-kit, and it should finish pressing out the bearing.
Pressing in the bearing with the kit should be no problem.
poor mans way to remove a wheel bearing
so if you're doing wheel bearings on a RWD truck or car MOST LIKELY this is the setup on the front wheel bearings, non sealed bearings anyway, so here's just a neat little trick I learned from my auto shop teacher and it sure came in handy today to not ruin anything. enjoy!
Hub Grappler ™ by OTC
OTC Hub Grappler™ by OTC
• The Hub Grappler Kit is the complete solution for
servicing wheel hubs and bearings on the vehicle
without removing the steering components or knuckle.
This eliminates unnecessary alignments or the use of a
shop press, cutting service time dramatically.
• The new Hub Grappler Puller is specifically designed
to apply maximum force with minimal effort from an
impact gun to also minimize service time.
• The new jaws are designed and sized to properly fit hub
applications and can be quickly located on the puller
bar without the use of fasteners.
• The new 3/4" custom drive screw coupled with the
special equalizer washer provides smooth operation
while the proprietary heat treating extends its life
5-10 times longer than similar designs.
• 6 new adapters increases application coverage up to
2009 model year. Also includes tie rod/ball joint tool
and 2 Ford axle installers.
• The new Hub Grappler Application Guide is the most
comprehensive hub and bearing service guide on the
market. Developed to be the first tool used in the kit,
it provides quick reference to the other tools in the kit
required to do the job, eliminating guesswork and
saving time. New and Improved Design
How To Install Replace Front Wheel Hub Bearing GM Front Wheel Drive PART 1 1AAuto.com
http://www.1aauto.com/1A/wheel-bearing-hub-front
1A Auto shows you how to repair, install, fix, change or replace a worn out, vibrating or groaning front wheel bearing hub. This video is a 1999 Pontiac Grand AM. This process is the same for many midsize GM front Drive Vehicles including Chevy Cavalier, Olds Achieva Cutlass Alero.
