How to build HORSEPOWER - Ford 461ci Windsor V8 by Dandy Engines
Engine specialists Dandy Engines building a small block Windsor 461ci
stroker for Pat Staplton. Follow the engine assembly as the guys aim to
make more than 820hp naturally aspirated on regular pump unleaded. Pat
plans on putting this brute of an engine into a Ford Falcon XD/XF Ute. [
Creative Commons music license CC 3.0
Jahzzar - Breaking Bad
CRANKWALKED? 7-bolt teardown 1080HD
Audio track by RojoDelChocolate.
Here's the 48,000 mile-old 7-bolt I blew up summer 2011 after over 150 drag
passes, a half dozen Dyno sessions, 4 transmissions,
3 clutches and 10 years of hard all-weather use.
Now this is a story all about how
My bearings got flipped-turned upside down
And I'd like to take a minute just sit right there
And tell you how I used to mix and burn my gas and my air.
In RVA suburbs born and raised
On the dragstrip is where I spent most of my days
Chillin out, maxin, relaxing all cool,
And all shooting some BS outside with my tools
When a couple of guys who were up to no good
Started running races in my neighborhood
I heard one little knock and my rods got scared
And said "You put it in the garage until you figure out where..."
I Begged and pleaded that it not be that way,
But it didn't want to start and run another day.
I kissed it goodbye, because the motor punched its ticket
I got out my camera, said "I might as well kick it."
Crankwalk yo this is bad
Drinking metal shavings from an oil pan.
Is this what the rumor of crankwalk is like?
Hmm this won't be alright
But wait I heard knocking, grinding and all that
Is this the type of failure that should happen to this cool cat?
I don't think so, I'll see when I get there
I hope they're prepared for this video I share.
Well I pulled all the bolts and when I came out
There were chunks in my fluids in the pan and they drained out
I aint trying to get depressed cause I got all my spares out.
I sprang into action like lightning disassembled
I whistled while I worked and my hands never trembled
The 7-bolt was FRESH with the shine like a mirror
If anything I can say this bling was rare
What I saw inside the engine stained my underwear.
I turned off the air compressor 'bout 7 or 8
And I yelled to crankcase "Yo holmes, smell ya later"
I looked at my internals they were finally there
To sit on my workbench and stink up the air.
Ferrari V12 Engine
Ferrari V12 Engine Assembly. From start to finish, one technician is
responsible for the assembly........
For more automotive news:
Follow us on Facebook:
Ferrari Formula 1 - Loud Start-up!
The music, the power and the vibe of an Italian supermonster! Look at these
Italian guys trying to start up this F1 car, and turn up that volume when
it finally starts. Enjoy the music transmitted by this beast/beauty.
Dont forget to look on my channel for more videos! I would appreciate your
comments and thumbs up! :D
F1 Engines (v8 vs. v10)
Hey guys and gals! I decided to compile a video for your viewing pleasure
comparing the sounds of a V8 and a V10 Ferrari F1 engine. I wanted to
capture an onboard view of the drivers making their hotlaps to make the
engine comparison more noticeable. The two drivers in the video are Kimi
Raikkonen and Michael Schumacher.
World smallest V12 engine
Apparently the builder's name is Yesus Wilder and he only used three
materials to build the engine. Stainless steel, aluminum, and bronze.
All credits to him.
BBC 1981: F1 engine failure mechanics
How a Cosworth DFV fails at high rev. Taken from 1981 BBC Horizon show
"Gentlemen, Lift Your Skirts."
(Full show can be found at http://vimeo.com/50943563)
AMG SPEEDSHIFT MCT
Mercedes AMG: Ever wonder what MCT stands for? This video explains the
technical aspects of the AMG SPEEDSHIFT MCT 7-speed sports transmission.
Nissan GT-R Engine Assembly
Here are some quick scenes from the Nissan Yokohama engine plant's Clean
Room. It takes an average of 100 minutes for an engine master to assemble
one engine. Each man diligently checks and records the torque spec of
every critical nut and bolt, and the data is stored for the life of the
Cylinder Bore Honing - Engine Building Video - Hone Piston Wall
Buy the "Basic Engine Building" DVD
Basic Engine Building DVD - Chapter 28: Honing
And finally we come to the main part of the machine shops job, honing the
cylinder walls. It will do two things. First it will bring the cylinder
walls to the matching diameter of the new pistons. Second it will leave a
cross hatch pattern of light scratches, to keep oil on the walls and
prevent metal on metal scraping. A dial bore gauge is used to bring it to
the exact spec needed within 1/10,000th of an inch.
BoxWrench.net is a community and resource designed for automotive
enthusiasts. The Basic Engine Building DVD is over three hours of engine
building that covers everything from removal and disassembly to final
assembly and engine start-up. This is the ultimate DVD for any home
mechanic or engine enthusiast that wants to see a complete rebuild from
Teardown to Start-Up. This video can be used to learn how to work on almost
any type of internal combustion engine including V8, V6, Straight 8,
in-line 6 and even 4 cylinder engines. All of the interactive features and
menus will not work over YouTube.
This video is great for people interested in car repair, car care, and
restoration. As well as hot rods, muscle cars, performance parts, and Boosting horsepower. It can also help
you to gain knowledge for increasing fuel economy, how to lower your
emissions, and covers preventative maintenance to avoid little things like
Don't forget our Holley Installation & Tuning DVD. Sample clips on our
youtube page and at our store here...
Get the full DVD with all of the interactive menus, Tools section and
engine Glossary terms here...
http://www.boxwrench.net - Educating the Automotive Enthusiast!
BoxWrench on Facebook: