2002 Ford Focus Clutch Replacement Video (Part 2) - EricTheCarGuy
Here is a link to the full video http://www.ericthecarguy.com/vmanuals/22-vmanual-store/71-2002-ford-focus-clutch-replacement-vmanual
Part 3: https://www.youtube.com/watch?v=rvuIFAWeFSQ
Well here is the second installment in the Focus clutch replacement video and we get a little farther in the process so sit back and enjoy watching me get dirty.
Click below and Stay Dirty
Visit me at EricTheCarGuy.com
Visit EricTheCarGuy Forum
Visit my Facebook Page:
Due to factors beyond the control of EricTheCarGuy, it cannot guarantee against unauthorized modifications of this information, or improper use of this information. EricTheCarGuy assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. EricTheCarGuy recommends safe practices when working with power tools, automotive lifts, lifting tools, jack stands, electrical equipment, blunt instruments, chemicals, lubricants, or any other tools or equipment seen or implied in this video. Due to factors beyond the control of EricTheCarGuy, no information contained in this video shall create any express or implied warranty or guarantee of any particular result. Any injury, damage or loss that may result from improper use of these tools, equipment, or the information contained in this video is the sole responsibility of the user and not EricTheCarGuy.
Trans & Clutch 4 - Installing The Clutch
What you wanted to know about clutches but were afraid to ask.
I'm putting a ACT MB1-XTSS on the car in this video. Step height, clutch dowell pins, bolt part numbers, alignment and various clutch parts are described in this video. It's part of an all-inclusive drivetrain tech piece I'm working on that's broken up into sections to maintain focus on the individual processes involved.
How to Change a clutch
I show u how to change a clutch on a Nissan hardbody but this will work for most older clutch's
Check these links
Lawrence's Facebook : http://Facebook.com/earthscraper69
Lawrence YouTube channel : http://www.youtube.com/user/earthscraper69
Diaphragm clutch alignment How to do it without a tool just by eye no alignment tool needed
This is some information on how to line up your clutch plate prior to tightenting the pressure plate up to the flywheel. Its easy to do without the tool if you take your time by eye and using a socket you will probably have lying around the job. I explain a bit about the clutch and what to look for and youu see the gearbox go back on afterwards. Why does a clutch squeak? check the plate springs look at the flywheel condition check the gearbox input shaft. Tons more on the dvd at www.diy-dvds.com Filmed at Buzbys Garage Chingford E4
Ford Ranger & Mazda B-Series Pickup Clutch Hydraulic Release System Bleeding Procedure Part 2
The Ford Ranger and Mazda B-Series are very challanging when it comes to bleeding the hydraulic clutch release system, specifically due to the trapped air in the master cylinder and pressure line. This video shows the technique that we use in our installation lab when we work on one and it is what we recommend to diagnosis the release system, identify the problem area and then "burp" and gravity bleed the system. If you have a question the best way to contact us is at 1-800-258-8312 press 4 8-5 EST. Presented by Gary Croyle.
Removal and Servicing of Clutch Master Cylinder to Slave Cylinder Connections
This video demonstrates the proper techniques for disconnecting and connecting the clutch hydraulic line at the concentric slave cylinder. These procedures apply to clutch hydraulics on various vehicles from the Ford, GM, Chevrolet and Dodge families.
(Presented by Gary Croyle of Perfection)
If you need help bleeding a clutch hydraulic system on a Ford Ranger or Mazda B Series pickup please refer to the following video:
Perfection Technical Hotline:
1-800-258-8312 then dial 4
Trans & Clutch 1 - Remove Transmission
This is the first in a multi-video series regarding clutch tech. The clutch itself is a simple mechanism, but it's buried deep in the engine, so you can't just cover the clutch. First, you have to cover how to remove the transmission to get to it.
This project started off strange, got kind-of not-good, and then took a turn for the worst. The typical clutch job is not as difficult as the next video will display, but it's good this happened to me because I film this kind of crap. If for some asinine reason you encounter the kind of failure I experienced, you'll know what to do after the next video. Clutch assembly will be covered in a third video.
About the car:
You saw the other assembly video. You know when I put this thing together. You know it doesn't come out to play when it's cloudy. I've had it on the road less than an earl change. Freshly rebuilt TRE Stage 2.5 trans with a brand new ACT 2600 and a sprung 6-puck (MB1-XTG6) on a stock flywheel. This is Transmission #4.
How manual transmission works. By: Kunal C.
We have made a new and improved video"How manual transmission works (Revised)", please watch.
How a manual transmission works (revised) part 1 http://www.youtube.com/watch?v=xIOEueaHvFo
Ford Ranger & Mazda B-Series Pickup Clutch Hydraulic Release System Bleeding Procedures
Video shows an easy way to bleed the clutch hydraulics on a Ford Ranger or Mazda B-Series pickup. We also have a video Ranger Bleeding Part 2 http://www.youtube.com/watch?v=91IYY_YENRw that shows the procedure on an actual truck. (Presented by Gary Croyle of Perfection)
Video Topics include:
- Describing symptoms of air trapped in the release system (i.e. no release, poor release, gear grinding, can't put into 1st or reverse)
- Bench Testing & Bleeding of Clutch Master Cylinder
- Testing Clutch Master Cylinder on Vehicle
- Inserting clutch line into new Perfection TECH-Link™ connector
- Gravity Bleeding of Slave Cylinder
- Demonstration of proper plate lift after successful clutch bleeding
This whole clutch bleeding procedure was done using absolutely NO special tools. Only a Philips screwdriver was used. You can easily do this too!
Try this procedure on your next Ford Ranger or Mazda pickup clutch job. You will be glad you did. It works, its easy and you will save lots of time!
Perfection Technical Hotline:
1-800-258-8312 then dial 4
TECHnovation™ Clutch Hydraulics....
Designed and engineered to install faster and easier than original equipment, using existing lines and no special tools!
Perfection offers a complete line of TECHnovation™ Clutch Hydraulics including concentric clutch slave cylinders, external clutch slave cylinders, clutch master cylinders and pre-filled units.
TECHnovation™ is the natural evolution to Perfection's "Service the System™" approach to clutch repair which leads to longer life and more importantly...happy customers.