HONDA V-Tec Operation
HONDA V-Tec Operation
Get the book here: https://www.createspace.com/4321251
Describes the operation of the HONDA V-Tec variable valve timing system.
Like never seen before, this animation goes into details on the mechanical
principle of the V-Tec system. The Honda V-Tec system is a dual setting
variable valve timing system. It is meant to give high efficiency and low
power at lower RPM and high power and low efficiency at higher RPMs. There
have been a few incarnations of V-Tec, which came out in the late 80's, but
their principle is the same. See it all here with high quality visual
Amazon Printed-Books & Kindle:
Google Play Android APPs:
Amazon Video DVDs:
Barnes & Noble Nook:
Apple iTunes iPad:
AFAccord's 417whp F23 Turbo Accord - HD Vids and Dyno
I only had a week to drive the car after it was tuned and wasn't able to
wire up my ECU switch in time to get any high Boost runs on video. Sorry guys! I'll make
plenty of high-Boost videos when I
come home, so subscribe!
Music rights belong to Gemini - Graduation of AEI Media.
Parts and Specs:
-F23 block, bored to 86.5mm
-Wiseco K20 spec pistons @ 10.2:1 compression
-SwainTech ceramic coating on piston crowns
-Crower F23 rods
-OEM main bearings (pink across all journals)
-ACL HX rod bearings
-Kaizenspeed balance shaft delete kit
-Bisimoto heat-shielding intake manifold gasket
-Bisimoto Pro valve springs
-Bisimoto Pro valve retainers
-Bisimoto cam gear
-Innovative 65A engine mounts
-Maxbore F23 throttle body
-MFactory limited slip differential
-DIY ramhorn turbo manifold
-DIY 2.5" charge piping from CXRacing
-28"x8"x3.5" FMIC from Go-Autoworks
-Triple-core half-size radiator from Go-Autoworks
-3" Straight pipe Exhaust
-3" Vibrant Flat black muffler
-Garrett T3/T4 57 trim turbo
-ACT Xtreme pressure plate
-ACT Streetlite flywheel
-ACT performance street disc
-Tial 38mm wastegate
-Tial Q BOV
-P61 OBD1 ECU
-Tuned using eCtune by the infamous... Joseph Davis!
2002 Dodge Ram 1500 Engine Swap 4.7L Part 1 - EricTheCarGuy
Link to full version of this video:
Link to part 2: http://www.youtube.com/watch?v=QES-WrAB1NI
Visit me at: http://www.ericthecarguy.com/
This truck has been a challenge for me over the past couple of weeks as you
will seen in the video. The lesson here is do your best to check the
engine out before you install it and even that may not be enough. Be
careful when doing a job like this especially if you are by yourself as you
can get seriously injured if your not careful so work carefully and
methodically and things should work out fine.
The music is from the site
under "Royalty Free Music", it's title is "Merry Go-Distressed", the
producer of the site allows the use of this music as long as credit is
given, hence the credit given here. Thank you!
Click below and Stay Dirty
Visit me at EricTheCarGuy.com
Visit EricTheCarGuy Forum
Visit my Facebook Page:
Be safe, have fun and stay dirty.
Due to factors beyond the control of EricTheCarGuy, it cannot guarantee
against unauthorized modifications of this information, or improper use of
this information. EricTheCarGuy assumes no liability for property damage
or injury incurred as a result of any of the information contained in this
video. EricTheCarGuy recommends safe practices when working with power
tools, automotive lifts, lifting tools, jack stands, electrical equipment,
blunt instruments, chemicals, lubricants, or any other tools or equipment
seen or implied in this video. Due to factors beyond the control of
EricTheCarGuy, no information contained in this video shall create any
express or implied warranty or guarantee of any particular result. Any
injury, damage or loss that may result from improper use of these tools,
equipment, or the information contained in this video is the sole
responsibility of the user and not EricTheCarGuy.
JDM H23A VTEC Swap for CB7 1991 Honda Accord - What to look for
For more info or if interested in purchasing a motor, call Ricky at:
This is one of many videos to come about my H23A swap for my 1991 Honda
Accord. Applies to 1990, 1992, & 1993 also. Stay tuned for more...
Honda Accord AEM V2 Cold Air Intake Installation
2002 HONDA ACCORD SPECIAL EDITION
2.3L, 4 Cylinder v-tec
Series F23A1 Engine
I'm no professional at this. I'm still very new and learning more about the
import tuner world.
I've never done an intake installation before and this one is my first.
Please don't over judge me too harshly.
The video was more for me on how to install it, but I thought I would share
this with everyone.
Enjoy the video!
H22 Accord Swap & Test Drive
Go to a Forum for swap info, please, youtube is for videos. ..Removing the
old F22B1 and installing a fresh H22A engine assembly on a friend's 95
JDM H22A engine/trans, manual tensioner conversion, chipped P28, EGR
blocked, FIV bypass, custom-bent uncut prelude power steering line, custom
IAB/VTEC relay system. No External Modifications...zzz