Inspecting the Timing Belt - AutoZone Car Care
In the second installment of the AutoZone Complete Car Care - Timing Belt
Series, Bruce Bonebrake shows you how to inspect your timing belt and how
to prepare for a timing belt installation. Find out what steps you need to
complete before you can replace your timing belt.
Get everything you need to do the job right at http://www.autozone.com
Timing Belt - the Forgotten Belt (by Dayco)
Timing Belt - the Forgotten Belt. This video stresses the importance of
checking and following the manufacturers recommended replacement interval
for the timing belt. Along with recommendations to replace the "hardware"
associated with the Timing Belt (Tensioner, Water Pump, and Idler Pulleys)
at the same time the Timing Belt is being replaced. To find out more
information on our Timing Belt, Timing Belt Kit, Water Pump Kit, and Timing
Component Kit, visit www.daycoproducts.com
weird rattling noise from timing belt?
Update 2 years later: Its now quieter. I think the timing belt rubbed off
some of the plastic housing, enough to make enough room for the belt to run
through. It could be at the brink of failure, but it drives fine as of
please help me find the problem.
camry 1998 4 cylinder 5s-fe 90,000 miles. it makes this loud annoying sound
when in cold start. if i rev it from idle to about 2000 rpm, the sound gets
louder. above 2000 rpm, the rattling sound cant be heard. after about 5-7
minutes, the car quiets down, but can still hear it. the sound is coming
from the lower side of the housing for the timing belt, near the
crankshaft. i bought it like this a few days ago. oil is full and clean.
the owner told me it was the timing belt that was recently replaced. but
why does it go quiet after the engine is warm if its the timing belt?
also, sometimes the brakes vibrate, even when the car is stopped.
Toyota Camry Timing Belt
TIMING BELT REPLACEMENT - 2.2L 5SFE - Toyota Camry
Toyota Camry Timing Belt Replacement
Autos & Vehicles
Timing Belt Replacement
1.Install No. 2 idler pulley (if removed). Install and tighten bolt to
specification. Ensure idler pulley is clean and rotates smoothly.
2.Install No. 1 idler pulley and tension spring (if removed). Pry No. 1
idler pulley away from timing belt area as far as possible. Temporarily
tighten No. 1 idler pulley bolt. Ensure idler pulley is clean and rotates
3.Using crankshaft pulley bolt, rotate crankshaft so timing mark on
crankshaft sprocket aligns with timing mark on oil pump housing. See. This
will position keyway in crankshaft sprocket at 12 o'clock position.
CAUTION:If reusing timing belt, ensure reference marks on timing belt align
with reference marks placed on crankshaft and camshaft sprockets. Ensure
timing belt is installed in original direction of rotation.
4.Ensure all sprockets and idler pulleys are clean. Install timing belt on
crankshaft sprocket, oil pump sprocket, No. 1 idler pulley, and then No. 2
idler pulley in sequence.
5.Install timing belt guide with cupped side away from crankshaft sprocket
and flat side toward timing belt. Install No. 1 timing belt cover and new
6.Align crankshaft pulley key groove with key in crankshaft. Install
crankshaft pulley. Install and tighten crankshaft pulley bolt to
7.Rotate crankshaft clockwise so cylinder No. 1 is at TDC on compression
stroke. Ensure timing mark on crankshaft pulley aligns with mark on No. 1
timing belt cover. If reusing timing belt, ensure reference mark on timing
belt aligns with upper edge of No. 1 timing belt cover.
8.Rotate camshaft, and align hole in camshaft sprocket with alignment mark
on camshaft bearing cap. Install timing belt on camshaft sprocket. If
reusing timing belt, ensure reference mark on timing belt aligns with the
reference mark on camshaft sprocket. Ensure tension exists on timing belt
between the crankshaft and camshaft sprockets.
CAUTION:DO NOT rotate crankshaft counterclockwise, as viewed from timing
belt end of engine.
9.Loosen No. 1 idler pulley bolt 1/2 turn. Rotate crankshaft pulley 2 full
revolutions clockwise from TDC to TDC. 10.Ensure timing mark on crankshaft
pulley aligns with "0" mark on No. 1 timing belt cover, and hole
in camshaft sprocket aligns with alignment mark on camshaft bearing cap. If
timing marks are not aligned, remove timing belt and reinstall. 11.Rotate
crankshaft clockwise 1 and 7/8 revolutions and align crankshaft pulley mark
with 45-degree Before Top Dead Center (BTDC) mark on No. 1 timing belt
12.Tighten No. 1 idler pulley bolt to specification. Install No. 2 timing
belt cover and gaskets. Install and tighten spark plugs to specification.
13.To install remaining components, reverse removal procedure. Install all
bolts/nuts on right (timing belt side) engine mount before tightening to
14.On Camry, when installing control rod and bracket on strut tower and
right (timing belt side engine mount, tighten bolts to specification in
SafetyDang Tv Timing Belt and Water Pump Ep 4
Please read the FSM for all torque specs.
In this video we change my timing belt and water pump in my 2002 Toyota
Tacoma. This engine is the 5vz-fe 3.4L V6. Note check your cam seals and
other seals that may need to be changed. Also if you know how to loosen the
tensioner you can change them if they are bad.
SST can be made or bought. Here is the thread on the topic:
Also snap-on tensioner tool can snap your lower pulley timing belt
tensioner. So take the time to remove your ac pump and the other bracket.
ALSO if you have red Toyota coolant continue to use RED Toyota coolant. You
can only go back to red coolant if you flush the radiator.
Changing a Timing Belt
The Repair Shepherd team is back with a new repair. This weeks job:
Replace a timing belt on a 2000 Toyota Avalon. See how easy a maintenance
job like this can be.
Check out all our related products at the following link:
Disclaimer: Use extreme caution whenever working on a motor vehicle.
AutoShepherd.com is not responsible for any damage or injury should you
choose to attempt this yourself.
Pt. 2 of 2: Timing Belt Service 7th Gen Honda Civic
CGHQ Website: http://www.classicgamershq.com
Part 2: This is a fully detailed timing belt service for a 2001-2005 Honda
Civic 7th generation vehicle. We replace the timing belt, a/c and
alternator belt, power steering pump belt, water pump, auto tensioner, and
crank shaft seal. This is a step by step procedure to do this service
successfully with a bit of time and patience. Be sure to subscribe. Thanks!
PART 1: http://www.youtube.com/watch?v=zUjHS_gmmMQ
Also check out the aftermath, motor mount repair video:
How to diagnose Toyota Timing Chain Rattle or Knock troubleshoot 22R 22RE 22RET
Every Toyota 22R series engine with the single row timing chain and plastic
timing guides (1983~ish - 1995) that I have ever purchased with over
100,000 miles on the engine has had a driver's side guide that was either
partially broken or just totally gone. To the untrained ear it sounds a
like the valves need adjusting, but in this video I'll show you how to
inspect, troubleshoot, and diagnose a broken driver's side timing guide.
It makes a great bargaining chip when you can show the seller that the
timing guide is broken and then inform them that it's an $800+ repair at a
shop. If you can fix it on your own it will only run you about $100 in
parts and a Saturday's worth of time.