Evinrude 300XP -91
After a few hours in the workshop..
The expansion chambers are "home made" by hydroforming. The original Exhaust is milled away and the engine
block is filled whit plastic.
This engine will get electronic fuel injection and will not be used in a
How to build HORSEPOWER - Ford 461ci Windsor V8 by Dandy Engines
Engine specialists Dandy Engines building a small block Windsor 461ci
stroker for Pat Staplton. Follow the engine assembly as the guys aim to
make more than 820hp naturally aspirated on regular pump unleaded. Pat
plans on putting this brute of an engine into a Ford Falcon XD/XF Ute. [
Creative Commons music license CC 3.0
Jahzzar - Breaking Bad
V8 S10 First Start
My 1987 Chevrolet S10 finally running again after the V8 swap, will post
motor specs later, needs some carb tuning and ignition timing work, but all
in all a good start, no oil leaks, fires, etc.
1989 S-10 for sale!! very straight truck. for sale on ebay. this truck is
tubbed in the rear with a 9 inch ford rearend 373 gears and mini spool..
2000 S10 w/ LT1 V8
I finally put together a video of my 2000 S10 with a LT1 engine and six
speed T56 transmission. The truck was bought brand new just for the build,
has never seen inclimate weather and now has only 19,000 miles on the body.
The engine and transmission had only 16,000 miles at the time of the build
and was freshened up bofore being transplanted. The donor car was a 1995
Trans Am. The engine has a stock bottom end with the heads reworked by Loyd
Elliott to his LE2 level. GM hot cam kit, ported intake with a holley 52 mm
throttle body and stock injectors. Computer tuned by PCM For Less. GM 8.5"
rear end narrowed to fit. 3:73 Richmond gears, Moser axles and a GM limited
slip differential. Rear frame section is also narrowed to allow for the 12"
wide wheels. Wheels are Bonspeed Sweep's, 18x8 front and 18x12 rear. The
video is amatuer at best. Only my second time using the camcorder. Also the
truck is filthy having sit all winter. I just wanted to get a video of it
with it's current engine because I am about to replace it with a new LT1
383 stroker and will post a new video once it is installed for comparison.
It will be a much better quality video I promise and it will also be
completely cleaned and detailed as I prepare to hit the local car shows and
cruise ins again this summer. I have owned the truck for going on two
years now purchasing it from the original owner and builder. I am very
proud to own it. It is as clean and as professional of a build as I have
ever seen. Thanks for looking and I hope you like it. Please feel free to
post any comments that you may have.
V8 s10 turbo walk around
this is my 89 s10 with a 355 cu sb and a 66 mm garret turbo pushin into it. I, twisted performance cutom
made all the tubing and headers from the ground up.. thanks for lookin and
please leave me some comments.
s10 v8 5.7L HO crate motor
finaly some clips of it on the street sorry for the poor video my bud
filming is a bit of a tard... the truck still have the old 4L60E tranny
with 126,000 miles on it... 3.42 limited slip rear end... stock vortec
intake and stock vortec tune... this truck is no where near finished just
together so i have somthing to drive lol ya its my DD!
My 1994 Chevy S10 Blazer
I have had the truck for 7 years and fiqured it was time to fix her up.
Its on 20in irocs, has new interior except the dash. truck has 249000
miles on it. All I have left to do is dash cover, paint, and put my new
4.3 in it. Tell me what you guys think.
Thanks for watching!
Avaliação GM S10 LTZ 4x4 200cv 2014
Avaliamos agora a ultima geração da Chevrolet S10, na versão topo de
linha LTZ equipada com tração 4x4. Veja como ela se comportou, em
diferença ao modelo anterior de 180cv. Acompanhe!
[ ---Para adquirir o adesivo oficial acesse goo.gl/txFn4Z e compre ja o