Just a vid of my build i have been working on for a while. I was going to leave the car all motor but i wanted to Boost it to make a lot more power so im not the slow one in One-Sixx. Thanks to One-Sixx Tuning for the parts and time helping me with the car, thanks to everyone at the shop and in the crew for the help with the car, thanks to Beeyond Engineering for building the motor and TNS Transmissions for putting the lsd in my trans. Enjoy the vid dont forget to rate comment and subscribe for more!
The Haycemobile - Build up - Part 1
This is a vid I put together for a mate.
It shows the awesome progression of his car over a clutch job that turned into a full on 4-year build. No holds barred. GT3076R, JE forgies, Eagle rods.
This is going to be a monster.
Stay tuned for part 2, the engine build, the interior and the initial tune.
Music by Deftones - Change (in the house of flies)
K24 Hatch Build
lil preview of how my hatch is coming along...Jdm Honda Civic Eg k Series
Alot more Mods To Comes =)
K20 Civic Build Part 3 of 3
K20Z1 MOTOR INTO A CIVIC EG. ENTIRE BUILD WAS DONE IN A GARAGE BY 3 PEOPLE. LUIS, ADRIAN AND MYSELF (JAIME). WIRE TUCK, BATTERY RELOCATION, SUB HARNESS..... OK SO IVE BEEN ASKED THIS A FEW TIMES NOW SO I WILL JUST POST IT IN THE DESCRIPTION. WHATZ THE COST OF MY BUILD? RIGHT NOW IM UP TO ABOUT 20,000. HOW LONG DID IT TAKE? IT TOOK ME ABOUT 6-7 MOS FROM START TO FINISH.
Team 1320 382whp All Motor K26 Eg Getting Ready For 2011 IDRC West Coast Nationals
idle and walking around Team 1320's All Motor Street Car. Getting her readyy to race IDRC at funtucky April 23rd. 67mm kinsler ITB w/ top feed injection. Custom GO-Pwr single lobe vtec killer camshafts, GO-Pwr k26 stroker kit, aebs sleeves, port flow head, aem ems, race pack data log and display dash, rywire milspec wiring harness, fuel lab fuel system with x8 ID injectors, GO-Pwr/PAR dog box transmission. GO-Pwr hood exit header, Q16 race gas skunk2 suspension and camber kit.
My Eg Project=)
This My 1992 Civic hatchback for now im working on the outside then im going start on the engine next.. ill be putting more pics as i get more stuff to for the car ill keep you guys updated
The Civic Build part 02
once again, me and my cousin building up our civic EGs. This is part 02 of the "series". Its kinda short but oh well, its not like we've done THAT much to them.
So far I got my car up and running. I'm going 8 psi on stock internals... lets see how long that will last xD. I've been doing mostly body work to it to see if I can get it sprayed soon.
My cousin on the other hand has a lot of work to do. starting with his motor. An LS/V-tec built for 20 pounds. Hes got most of his forged internals, hes just missing two or three parts then its off to the machine shop to get the block bored 10 over, but his main focus right now is on getting his roll cage in so he can paint his car and assemble it.
Yea... its kinda short. I know... part 03 will make up for that.
Heads Cam 125 Shot C5 Corvette vs Bolton, 60 Trim, 272 Cams, 25 psi on E85 DSM/Stock block Both on Drag Radials last nights runs...2011. Floor was super sticky! Werns DSM Doing damage. vs White Corvette recorded using my iphone4. lol...AWD Talon VS. Corvette Vs.DNR K-Series Insight. Oakland, California. Subie vs evo9 bay area racing
Wiz- When i'm gone
Wiz-On my level
Lil Wayne- Prostitute part2
gsr turbo build
Here is a clip of my long awaited gsr turbo build. Enjoy, and be sure to check out more track vids @ http://www.youtube.com/watch?v=j0xoYv1gdXU. NTENSE baby!
Special thanks to Gabe Hin for all the help.
------------The car 2 yrs after (2012)-----------
Childstar's EK civic hatch
Just having a little fun with my camera and cruising around in the EK.
*build thread* @ http://www.clubcivic.com/board/showthread.php?t=204688
Be sure to check out SINCERE's music and videos!