Vauxhall Corsa 2004 1.2 Z12XEP Timing Chain Fail.Vehicle had coverd 35,000 miles.The timing chain was so slack that it had been wearing on the inner timing chain cover.A full timing chain set was replaced inc cam pullys all genuine parts used.
How To Torque Cylinder Head Bolts - EricTheCarGuy
How To Torque Cylinder Head Bolts - EricTheCarGuy
http://www.ericthecarguy.com/
Well this was a fun one to make. I believe I covered everything but if you feel I haven't please let me know in the comments below as well as any tips you might have to add as well. I'm not trying to make a big deal about "pound feet" or "foot pounds" I'm just trying to put that out there, the important thing is that you get the proper torque and get the job done right in my opinion, what you decide to call it is up to you.
---
Click below and Stay Dirty
Visit me at EricTheCarGuy.com
http://ericthecarguy.com/
Visit EricTheCarGuy Forum
http://www.ericthecarguy.com/forum/default.aspx
Visit my Facebook Page:
http://www.facebook.com/EricTheCarGuy
---
ETCG
Due to factors beyond the control of EricTheCarGuy, it cannot guarantee against unauthorized modifications of this information, or improper use of this information.  EricTheCarGuy assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. EricTheCarGuy recommends safe practices when working with power tools, automotive lifts, lifting tools, jack stands, electrical equipment, blunt instruments, chemicals, lubricants, or any other tools or equipment seen or implied in this video.  Due to factors beyond the control of EricTheCarGuy, no information contained in this video shall create any express or implied warranty or guarantee of any particular result. Any injury, damage or loss that may result from improper use of these tools, equipment, or the information contained in this video is the sole responsibility of the user and not EricTheCarGuy.
Vauxhall 1.9 CDTi Timing Belt Renewal Guide.wmv
A video guide to replacing the timing belt on a Vauxhall/Fiat 1.9 CDTi 150 engine. Use in conjunction with a Haynes manual or similar and only attempt if you feel confident enough and can afford to ruin your engine if you get it wrong...
Spring burnout Opel corsa
Running on gasoline. A bit too rich on fuel at the moment.
Throttlewire came of during the first burnout.
Timing Belt - the Forgotten Belt (by Dayco)
Timing Belt - the Forgotten Belt. This video stresses the importance of checking and following the manufacturers recommended replacement interval for the timing belt. Along with recommendations to replace the "hardware" associated with the Timing Belt (Tensioner, Water Pump, and Idler Pulleys) at the same time the Timing Belt is being replaced. To find out more information on our Timing Belt, Timing Belt Kit, Water Pump Kit, and Timing Component Kit, visit www.daycoproducts.com
Astra Turbo - Rocker Cover Gasket Renewal
My first video, it's a bit slow and boring. But was a good test.
On an engine with hydraulically adjusted valve clearance, the rocker cover gasket may never get changed in routine maintenance.
The gasket on this car hasn't been changed for 120,000km's and was leaking quite badly.
New gasket = cleaner engine bay :)
Astra Turbo (z20let) Timing Belt Install - Part 1 of 2
Warning. Serious damage may occur to your engine if the timing marks are not correctly positioned. Only undertake if you have the tools and the confidence for such a job.
Please source other advice and guides to compliment this video.
Time lapse installation video of removing the z20let timing belt and replacing the water pump. Installing the new timing belt is in part 2.
Corsa B X10XE Problem
Motor startete nicht richtig.
Drosselklappe war verdreckt und der Kühlmitteltemperatursensor war defekt.
Corsa Timing x264 (1.2 Engine)
This is how to set your timing on you twin cam corsa. It is not as difficult as some make it to be. You only need some patience and a steady hand.
If for any reason when you are done you get a cam positioning sensor fault code, please do not go buying one yet, just take time out and inspect the timing taking time to make sure that the arrow on the bolt flange point in the middle direction of the cam sensor.
If your timing it out, you would likely get a cam positioning sensor fault code.
Further more, it might be much easier to use a metal straight bar across the two cams for better comparison of their position, if you have ever bought a laminate fitting kit then the flat metal is the perfect candidate for it ; thought you would have to cut it to size.......
