In this video I show how to remove the flywheel from a 1982 XR200R without using any special tools. I learned this trick from watching a video an lawnmowers from the davidsfarm youtube channel.
For an alternative method, you can also use the rear axle bolt to fit into the larger thread instead of the smaller M12, and then hit it in the opposite direction without the screwdriver. In this case though, it did not fit. I know this works for some XRs, but not mine.
Trail Tech Z400 Flywheel Video Tutorial
Trail Tech video tutorial shows removal of the LT-Z400 stock flywheel and
installation of a Trail Tech replacement flywheel. Good for 2002-2008
how to remove a stator plate on a pitbike
Hope this helps, if you need any more help please comment below, and we
will try our best to help. Go check out our website www.pitbikeparts.co.uk
and view our facebook fan page.
Stators & Regulators/Rectifiers - What you need to know? - Video Guide: Tip of the Week
Kyle Bradshaw of Cruiser Customizing meets with Trent Kirby of ElectroSport
for the lowdown on Stators and Regulator/Rectifiers! Learn all you need to
know about them. What exactly it does? What are the features and benefits
of stators & rectifiers / regulators.
Youtube Channel: http://www.youtube.com/user/CruiserCustomizing - SUBSCRIBE
Stators create power in AC, the Rectifier converts AC power to DC power,
and the Regulator regulates the proper amount of power to the battery. Also
watch How to Install the Regulator / Rectifier on a Honda VTX1800 Retro!
Take a look!
australian6 is our Cruiser of the Week! Check out his australian6's Video
Introduction and Member Profile!
Thank You for watching this Cruiser Customizing Tip of the Week!
Until Next Week,
Take Care & Ride Safe!
Kyle Bradshaw aka: manybikes
Starter Clutch install on 660 Raptor
My first attemp of installing the one way starter clutch bought from L&A. I
know for a second there i had it wrong way round but got there in the end
and so far its worked a treat. I probably should have filmed some extra
bits from start to finish but hope this will come in handy to some one out
there. Also prob should have torque renched the main nut on ..
We demonstrate how to spilt a case and remove the crankshaft from a motorcycle or ATV Engine
Using a crankcase splitter / crankshaft remover from
http://www.rent-these-tools.com , we demonstrate splitting the crank case,
and removing the crankshaft from a Polaris Predator 500. This video is
provided as a general reference. You should consult your service manual
for specific procedures for your application.
On some motors, this tool is a necessity for replacing or rebuilding the
crankshaft, replacing worn crankshaft bearings, or repairing the
Replacing a BMW Self-adjusting Clutch & Dual-mass Flywheel Part 1 of 2
www.bavauto.com -- In this How-To DIY video series (Part-1 and Part-2) we
will be replacing a typical BMW clutch and flywheel. For more details on
this DIY, see our Tech Blog at www.blog.bavauto.com/go/clutchrepair .
These videos show the full removal, replacement and reassembly of the
self-adjusting clutch (SAC) and dual-mass flywheel, special instructions
that MUST be followed in the installation of the self-adjusting clutch,
failure modes of the dual-mass flywheel and finally, installation of the
UUC lightweight flywheel and performance clutch. We will also install the
UUC Short Shift Kit and DSSR. See the separate DIY video for the shifter
install at www.blog.bavauto.com/go/shortshift . All of the parts shown in
this DIY series are available at Bavarian Autosport. Visit our online
store at www.bavauto.com or call or knowledgeable agents at 800-535-2002.
Don't forget to "like" this video and send us some comments!