383, 388 stroker chevy with comp cams big mutha thumpr
This is a 388 chevrolet engine cold start up. It has a big mutha thumper
cam and 492 dumble hump heads. Heads have been angle milled and bowl
ported with light porting. flat top pistons and block been decked giving
aprox 11.7:1 static compression. 750 edelbrock carb and a dual plane high
rise air gap intake. This is all in a 1960 Chevy truck frame that im
restoring right now. Engine is backed with turbo 350 and ford 9 inch.
Cam Replacement on a Harley Davidson Twin Cam, including Pushrod Removal • J&P Cycles
Watch as Justin Bramstedt, Research Manager at S&S Cycle, walks you through
the process of upgrading the stock cams on a Harley Davidson FLTRX. The S&S
510C camshaft set is designed to be used with the stock Twin Cam
chain-drive system and is an economical way to improve the performance of
stock twin cam engine. In this video we'll see the easiest way to remove
your stock pushrods using a bolt cutter.
Shop for S&S Performance parts and more at
Shop the World's Largest Aftermarket Motorcycle Parts and Accessories
How-To Tear Down a Chevy 350 V8 Small Block Engine
Chris Duke from Motorz TV http://www.motorz.tv shows you how to tear down a
junk yard small block Chevy 350 engine to prepare it for rebuild.
Show notes: http://www.motorz.tv/small-block-teardown/
Watch the complete Chevy 350 engine rebuild series:
1. Tear Down: http://youtu.be/LZO1fWVxN4c
2. Machine Shop: http://youtu.be/e3r3wRBoXkk
3. Bottom End: http://youtu.be/gfrYWKi78zc
4. Top End: http://youtu.be/g46s-Vr4Br0
5. Finale: http://youtu.be/mvJNMN-oP68
ZR1 Vette vs Jet! - Chevrolet Corvette ZR1 Races A U.S. Navy Fighter Jet
MT Editor at Large Arthur St. Antoine pits Chevy's awesome "Blue Devil" --
the Corvette ZR1 -- against its toughest adversary yet: a Blue Angels
F/A-18 Hornet fighter jet.
Shot By: Jim Gleason & Terren Lin
Edited By: Jim Gleason
Read the story here:
Chevy 383 Stroker with Big Muther Thumper Roller Cam
Here we built and Dyno
tested this Small Block Chevy 383 stroker using the Comp Cams Big Muther
Thumper hydraulic roller camshaft. This engine made great power and killer
bottem end torque. If your looking for an awsome sound, these are the cams.
They sound bad A##. We build custom street / strip race engines. This would
be a great crate engine for your Nova, Chevelle, Camaro, Nova II, S10, El Camino,
Corvette or Monte Carlo. Give us a call to build yours. We can build any
street / strip or race engine from 300 - 2500 horsepower.
www.cnc-motorsports.com or call toll free 800-341-1528
350 with Comp Cams Magnum 270H 112 LSA and 4/7 swap
This was my first time swaping a sbc cam. I left the 081 heads stock on my
350, but put new extreme push rods, 270h cam, and lifters. So, you can run
a .470 lift cam on stock heads. I spent many weeks looking for that answer
ans now I have the experience for my self. I also could not find a good
sound clip of this special grind cam online- so now there is one....enjoy!
Comp Cams Magnum hydraulic flat tappet grind #12-211-2, with two changes...
it has the 4/7 swap and LSA is 112 (instead of 110).
Built for 1.6 rockers, lift is .501"/.501
(If used with 1.5 rockers, lift would be .470)