When you click on links to various merchants on this site and make a purchase, this can result in this site earning a commission. Affiliate programs and affiliations include, but are not limited to, the eBay Partner Network.
Price: $98.99
Description
Quantity: 4pcs
Vehicle Bolt Pattern: 8x170mm
Wheel Bolt Pattern:8x6.5
Thickness: 1.5inch
HubBore: 130 mm
Thread Pitch: M14x1.5 Studs & Lug Nuts
Compatibility
1999-2009 Ford F-250(CHECK THREADS-Can be 14x1.5 or 14x2)
1999-2016 Ford F-250 Super Duty(CHECK THREADS-Can be 14x1.5 or 14x2)
2017-2019 Ford F-250 Super Duty
1999-2016 Ford F-350(CHECK THREADS-Can be 14x1.5 or 14x2)
1999-2016 Ford F-350 Super Duty(CHECK THREADS-Can be 14x1.5 or 14x2)
2017-2019 Ford F-350 Super Duty
2003-2005 Ford Excursion
NOTE:
Please make sure that these are the correct application for your vehicle. We do not guarantee any fitment onto any vehicle,we only guarantee that you will receive the item described as the above. Returns are only accepted if unused and not installed.(ReturnsARE NOT ACCEPTED IF SPACERS-ADAPTERS HAVE BEEN INSTALLED TO YOUR VEHICLE)
INSTALLATION TIPS
1.Please Make Sure You Take The Proper Measurements Before Purchasing.
2.Make Sure You Get 5-7 Turns Before Tightening.
3.Suggested To Be Torqued Down By Hand At 85 FT/LBS.
4.The Back Of The Adapter Must Sit Flush On The Hub.
How to choose the correct wheel spacers:
STEP. Check 3 specifications
The following is the easy and simple way tocheck the bolt pattern/PCD, center/hub bore and thread pitch. If you donot sure, please just message us with the year, make and model of vehicle.
1). Check Vehicle Bolt Pattern/PCD For 4-lug, 6-lug, 8-lug, measure the segment from the CENTER of a bolt hole TO the CENTER of another hole. 5 lug is different, you need to measure the back of the hole to the center of the second bolt hole (not center point).(See Bolt Pattern Diagram below)
2). Check Vehicle Hub/Center Bore Size Measure the diam of the center bore on hub, make sure the spacer\'s diam is equal to or bigger than the axle diameter.
3). Check Vehicle Thread Pitch There are different types of studs, such as M12x1.25, M14x1.5, M12x1.5, 1/2\"x20, 9/16\"x18, please make sure the studs of wheel spacers is the same as the vehicle\'s, otherwise the spacer will not fit.
How to install the wheel spacers:
1).IMPORTANT - ADAPTER OR SPACER MUST SIT FLUSH AGAINST VEHICLE HUB, AND WHEEL MUST SIT FLUSH AGAINST ADAPTER OR SPACER!Stock studs must be trimmed down (shortened) if they protrude past the surface of the adapter or spacer. If not, vibration or other problems can occur. Some wheels have pockets that may allow for no stud trimming. If not, studs MUST be trimmed.
2). Make sure the mounting surface (vehicle hub) is clean and flat, and remove all retaining clips.
3). Install the adapter to the vehicle, with the proper lug nuts, and torque to manufacturer’s wheel torque specs.
4). Install the wheel to the adapter by torquing to the vehicle manufacturer’s wheel torque specifications (again, max 140 ft-lbs). Please assure the proper thread engagement (6 to 8 full turns) on lug nuts or bolts.
5). Drive the vehicle. If no problems (noise, vibration, anything out of the ordinary), drive about 5 miles, then re-torque the lug nuts attaching the spacer or adapter to the hub.