When you click on links to various merchants on this site and make a purchase, this can result in this site earning a commission. Affiliate programs and affiliations include, but are not limited to, the eBay Partner Network.
Price: $47.93
Specifications:
1) Thickness: 1" / 25mm
2) Vehicle Bolt Pattern(PCD): 5x120mm
3) Wheel Bolt Pattern(PCD): 5x120mm
4) Hub Diameter: 72.6mm / 2.86"
5) Thread Size: 12x1.5 / M12x1.5 / 12mmX1.5
Note:Please make sure you take the proper neasurements gefore purchasing
Package include: 2Pcs Wheel Spacers Adapters
What should I pay attention to during installation?
1) Check to make sure that the wheel spacer fits perfectly with the hub/axle stub and the inner mounting surface of the wheel.
2) Make sure that the wheel bolts being used are of the appropriate length, not too long or too short.
3) DO NOT proceed if both of the wheel spacer do not fit.
4) Please be sure to clean the rust on the hub before starting the installation, otherwise it will affect the working life of the spacers.
5) Make sure that you get 5-7 FULL TURNS of the lugs when installing. Torque them down to the manufacturers specs (up to and not greater than 110ft lbs).
6) Avoid using an impact wrench because improper usage may cause the lug nuts/bolts to break or loosen while driving causing a potential injury or accident.
7) All lug nuts, bolts and torque must be checked after driving the first 50 miles after installation. Afterwards, please check all lug nuts and bolts every 3,000-5,000 miles.
8) Alignment is necessary after installation, this will prevent any wobble and vibration from occurring.
How to measure the fender gap to choose suitable thickness?
1) Line up a straight edge ruler against the sidewall of the tire, use the measuring device to measure from the inside of the ruler to the inner fender lip.
2) Please take multiple measurements and use the smallest data point.(The most closest spot may be at the front or rear edge of the fender). The maximum recommended spacer
thickness= the smallest gap - 3/8"(10mm)
About the wheel bolts:
Your Factory wheel studs may extend past the surface of the wheel spacers. In this case you will need to:
1) Shorten the factory studs.
2) The wheels need to have the open slots (cavities) between mounting holes.
3) Purchase a set of shorter studs and replace them with the factory studs.
Vehicle Fitment Information:
BMW:
1 SERIES (E82, E88) - 128i, 135i, M1, 1M COUPE
3 SERIES (E30) - M3
3 SERIES (E36) - 318i, 318is, 318ti, 325i, 325is, 328i, 328is, M3
3 SERIES (E46) - 323ci, 323i, 325ci, 325i, 325xi, 328ci, 328i, 330ci, 330i, 330xi, M3
3 SERIES (E90, E91, E92, E93)-325i, 325xi, 328i, 328xi, 330i, 330xi, 335d, 335i, 335is, 335xi, M3
5 SERIES (E28, E34) - 525i, 528e, 530i, 535i, 535is, 540i, M5
5 SERIES (E60, E61 2004-2010) - 525i, 525xi, 528i, 530i, 530xi, 535i, 535xi, 545i, 550i, M5
6 SERIES (E24, E63, E64) - 633i, 635i, 645ci, 650i, M6
7 SERIES (E23, E32, E38) - 730i, 730il, 733i, 735i, 735il, 740i, 740il, 750i, 750il
8 SERIES (E31) - 840ci, 840i, 850ci, 850i
1996-2002 Z3 (TYPE RC)
1998-2002 M-COUPE/ROADSTER (TYPE MRC)
2003-2009 Z4 (E85, E89)
2006-2008 Z4 M COUPE/ROADSTER (M85)
2000-2003 Z8 (E52)
Before&After
Item SpecificsManufacturer Part Number TOP11540101advBrand top-liftsupportType Wheel SpacersInterchange Part Number 5x120 Wheel Spacers Adapters 5 LugOther Part Number 1" or 25mm Thick Wheel SpacersSuperseded Part Number fits 2002 2003 2006 2008 BMW 325i 2008 BMW 335xiThickness 1" or 1 Inch or 25mmThread Size 12mm x 1.5 or 12x1.5 or M12x1.5Stud Grade 10.9Vehicle Bolt Pattern 5x120mmWheel Bolt Pattern 5x120mmMaterial High Grade T6-6061 Billet AluminumSurface Finish CNC Machined Polished Aluminum FinishColor SilverPlacement on Vehicle LeftVehicle Fitment For BMWCenter Bore Size 72.6mmHub Centric YesQuantity 2pcsWarranty 1 Year Item SpecificsManufacturer Part Number TOP11540101advBrand top-liftsupportType Wheel SpacersInterchange Part Number 5x120 Wheel Spacers Adapters 5 LugOther Part Number 1" or 25mm Thick Wheel SpacersSuperseded Part Number fits 2002 2003 2006 2008 BMW 325i 2008 BMW 335xiThickness 1" or 1 Inch or 25mmThread Size 12mm x 1.5 or 12x1.5 or M12x1.5Stud Grade 10.9Vehicle Bolt Pattern 5x120mmWheel Bolt Pattern 5x120mmMaterial High Grade T6-6061 Billet AluminumSurface Finish CNC Machined Polished Aluminum FinishColor SilverPlacement on Vehicle LeftVehicle Fitment For BMWCenter Bore Size 72.6mmHub Centric YesQuantity 2pcsWarranty 1 Year
WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov.
1.We only accept PayPal.
2.Please do not use the PayPal note field to indicate us to ship to other address. The note there will NOT be read. If you want to change the shipping address, please contact us by eBay messages.
3.(if you want cancel orders or change address pls contact us within 6 hours after payment,or we are not responsible for shipping a replacement.)
4.Payment must be received within 10 days as auction ended or order might be delayed.
1.We only accept PayPal.2.Please do not use the PayPal note field to indicate us to ship to other address. The note there will NOT be read. If you want to change the shipping address, please contact us by eBay messages.3.(if you want cancel orders or change address pls contact us within 6 hours after payment,or we are not responsible for shipping a replacement.)4.Payment must be received within 10 days as auction ended or order might be delayed.1.We only accept PayPal.2.Please do not use the PayPal note field to indicate us to ship to other address. The note there will NOT be read. If you want to change the shipping address, please contact us by eBay messages.3.(if you want cancel orders or change address pls contact us within 6 hours after payment,or we are not responsible for shipping a replacement.)4.Payment must be received within 10 days as auction ended or order might be delayed.1. Orders processed within 24 hours of payment verification.
2. We only ship to confirmed PAYPAL addresses. Your PAYPAL address must match your Shipping address.
3. The images shown are not the actual item and are for your reference only.
4. Fast shipping:All our packages use USPS First Class/UPS/Fedex.... Package Service
5. If you have not received your shipment within 15 days from payment , please contact us. We will track the shipment and get back to you as soon as possible with a reply. Our goal is customer satisfaction!
1. You have 30 days to contact us and 10 days to return it from the date it was received. If this item is in your possession more than 7 days, it is considered used and we will not issue you a refund or replacement. There are NO EXCEPTIONS!
2. All returned items must be in the original packaging and you must provide us with the shipping tracking number, specific reason for the return, and item custom lable.
3. We will refund your full winning bid amount, upon receipt of the item in its original condition and packaging with all components and accessories included, AFTER both Buyer and Seller cancel the transaction from eBay. OR, you may choose to have a replacement.
4. Return shipping is to be paid by the Buyer.
We maintain high standards of excellence (five stars review)and strive for 100% customer satisfaction! FEEDBACK IS VERY IMPORTANT TO US. We request that you contact us immediately BEFORE you give us neutral or negative feedback, so that we can satisfactorily address your concerns.
New List Item Top Luggage Carrier Crossbar Roof Rack Bar Rail For 2017-2020 Kia Sportage USD 74.64 For 2009-2015 GLK 280 GLK350 Roof Rack Extension Luggage Carrier Well-made USD 85.40 1 set Bicycle top tube adapter Roof Rack Universal Material iron Cargo Well-made USD 38.02 2 pcs Black Roof Rack cross bars Rail For RAV4 2019 Carrier Aluminum baggage new USD 75.62 Adjustable 2 Bar Van Ladder Roof Rack Heavy Duty 700Lbs Steel Rear Cargo White USD 78.77 Hot Item 2 Rear Trunk Liftgate Tailgate Hatch Lift Support For 99-04 Suburban Tahoe Yukon USD 23.69 2 Front Hood Lift Supports Struts Struts Gas Spring For 2002-2007 Jeep Liberty USD 16.19 For 98-02 Toyota Corolla Interior Front Rear 4Pcs Door Handles Inside USD 11.18 For 99-04 Jeep Grand Cherokee 2 Hood+2 Tailgate+2 Window Lift Supports Gas Strut USD 30.69 Qty(2) For Honda Accord 2003-2007 Front Hood Lift Supports Gas Prop Struts Shock USD 18.88 Shop CategoryStore Home Body Kits◈Front Bumper Lip Lift supports Wheel hub Radiator&Condenser remote key side Marker Light Mirrors Wheel Spacers Leveling Lift Kit Cylinder Head Gasket Sets AC Compressor Shocks & Struts CV axle Brake Pads & Rotors◈Brake Pads◈Brake Pads and Rotors Fuel injectors Coilover Air Suspension Complete Strut Cylinder Piston Gasket Sets Car Tools Valve Cover Door Lock Actuator Power Steering Pump Variable Timing Solenoid (VVT) Electric Water Pump Timing Chain Kits Timing Belt Kits Water Pumps Strut Tie Bar Throttle Body Harmonic Balancer Oil Pan Intake Manifold Radiator Coolant Tank HVAC ATV Rear Wheel Axle Car Antenna ABS Wheel Speed Sensor Spoilers & Wings Thermostat Housing Regulator Rectifier Oil Cooler Starter Relay Knock Sensor Turbocharger Parking sensor Window Switch Window Regulator Ignition coil Detection tools Crankshaft Position Sensor Camshaft Position Sensor MAP Sensor Oil Pressure Sensor Throttle Position Sensor Stator Catalytic Converter Transfer Case Shift Motor Secondary Air Injection Pump Running Board Motor Clutch Slave Cylinder Consoles & Parts Towing & Hauling Door handles Bumper Roof rack Tire Pressure Gauge Steering Rack starter Spark Plug Ignition Wire Engine Mount Glow Plug Air Cleaner Filter Box Pressure Tester Gauge Jack Stands Sun Visor alternator ATV Brake Caliper Interior LED Light ignition distributor Car Carburetor Air Intake Hose Cold Air Intake Kit Steering U-Joint Height Level Sensor Temperature Sensor Driveshaft Vacuum Actuator Ballast module Rubber Seal Strip Nerf Bars ATV Brake Master Cylinder Fuel Injector Wiring Harness Oil Fuel Hose Line LED headlight Assembly headlight motorcycle water Pump Impeller Rocker Arm Hydraulic Lifter&Roller Lifter Oxygen Sensors Sensor-8 Steering Shaft transmission filter transmission kit Fuel Pumps Windshield Wiper Motor Jeep9 CDI BOX Proportioning Valve suspension kit Strut Mount Kit Crankshaft Pulley 4 Pcs wheel hub bearing Fender Flares jumper cable ATV Tires Tonneau Cover Window Visor Bug Shield dash cover tire pressure sensor fastener Switch Panel vehicle speed sensor Pillar Posts Cargo Cover Hub Caps fog lights ATV Ignition Switch Windshield Outer Trim Fuse Holder Box Suspension+Strut+Bearing Rear View Camera Car Seat Cover Window Louver Cover other golf cart parts winch AC Compressor Control Valve leveling kit + struts shocks Dash Cover Radiator Shutter Tensioner License plate frame battery Switch Air suspension valve solenoid PTO Clutch Spindle assembly car CV axle Instrument Panel light 3rd Third Brake Light transfer case chain Diesel Air Heater Other 2x 1 Inch 5x120 Wheel Spacers 12x1.5 Fits BMW E46 325i 325xi 335xi 328ci 328i M5Specifications:
1) Thickness: 1" / 25mm
2) Vehicle Bolt Pattern(PCD): 5x120mm
3) Wheel Bolt Pattern(PCD): 5x120mm
4) Hub Diameter: 72.6mm / 2.86"
5) Thread Size: 12x1.5 / M12x1.5 / 12mmX1.5
Note:Please make sure you take the proper neasurements gefore purchasing
Package include: 2Pcs Wheel Spacers Adapters
What should I pay attention to during installation?
1) Check to make sure that the wheel spacer fits perfectly with the hub/axle stub and the inner mounting surface of the wheel.
2) Make sure that the wheel bolts being used are of the appropriate length, not too long or too short.
3) DO NOT proceed if both of the wheel spacer do not fit.
4) Please be sure to clean the rust on the hub before starting the installation, otherwise it will affect the working life of the spacers.
5) Make sure that you get 5-7 FULL TURNS of the lugs when installing. Torque them down to the manufacturers specs (up to and not greater than 110ft lbs).
6) Avoid using an impact wrench because improper usage may cause the lug nuts/bolts to break or loosen while driving causing a potential injury or accident.
7) All lug nuts, bolts and torque must be checked after driving the first 50 miles after installation. Afterwards, please check all lug nuts and bolts every 3,000-5,000 miles.
8) Alignment is necessary after installation, this will prevent any wobble and vibration from occurring.
How to measure the fender gap to choose suitable thickness?
1) Line up a straight edge ruler against the sidewall of the tire, use the measuring device to measure from the inside of the ruler to the inner fender lip.
2) Please take multiple measurements and use the smallest data point.(The most closest spot may be at the front or rear edge of the fender). The maximum recommended spacer
thickness= the smallest gap - 3/8"(10mm)
About the wheel bolts:
Your Factory wheel studs may extend past the surface of the wheel spacers. In this case you will need to:
1) Shorten the factory studs.
2) The wheels need to have the open slots (cavities) between mounting holes.
3) Purchase a set of shorter studs and replace them with the factory studs.
Vehicle Fitment Information:
BMW:
1 SERIES (E82, E88) - 128i, 135i, M1, 1M COUPE
3 SERIES (E30) - M3
3 SERIES (E36) - 318i, 318is, 318ti, 325i, 325is, 328i, 328is, M3
3 SERIES (E46) - 323ci, 323i, 325ci, 325i, 325xi, 328ci, 328i, 330ci, 330i, 330xi, M3
3 SERIES (E90, E91, E92, E93)-325i, 325xi, 328i, 328xi, 330i, 330xi, 335d, 335i, 335is, 335xi, M3
5 SERIES (E28, E34) - 525i, 528e, 530i, 535i, 535is, 540i, M5
5 SERIES (E60, E61 2004-2010) - 525i, 525xi, 528i, 530i, 530xi, 535i, 535xi, 545i, 550i, M5
6 SERIES (E24, E63, E64) - 633i, 635i, 645ci, 650i, M6
7 SERIES (E23, E32, E38) - 730i, 730il, 733i, 735i, 735il, 740i, 740il, 750i, 750il
8 SERIES (E31) - 840ci, 840i, 850ci, 850i
1996-2002 Z3 (TYPE RC)
1998-2002 M-COUPE/ROADSTER (TYPE MRC)
2003-2009 Z4 (E85, E89)
2006-2008 Z4 M COUPE/ROADSTER (M85)
2000-2003 Z8 (E52)
Before&After
WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov.
1.We only accept PayPal.
2.Please do not use the PayPal note field to indicate us to ship to other address. The note there will NOT be read. If you want to change the shipping address, please contact us by eBay messages.
3.(if you want cancel orders or change address pls contact us within 6 hours after payment,or we are not responsible for shipping a replacement.)
4.Payment must be received within 10 days as auction ended or order might be delayed.
1.We only accept PayPal.2.Please do not use the PayPal note field to indicate us to ship to other address. The note there will NOT be read. If you want to change the shipping address, please contact us by eBay messages.3.(if you want cancel orders or change address pls contact us within 6 hours after payment,or we are not responsible for shipping a replacement.)4.Payment must be received within 10 days as auction ended or order might be delayed.1.We only accept PayPal.2.Please do not use the PayPal note field to indicate us to ship to other address. The note there will NOT be read. If you want to change the shipping address, please contact us by eBay messages.3.(if you want cancel orders or change address pls contact us within 6 hours after payment,or we are not responsible for shipping a replacement.)4.Payment must be received within 10 days as auction ended or order might be delayed.1. Orders processed within 24 hours of payment verification.
2. We only ship to confirmed PAYPAL addresses. Your PAYPAL address must match your Shipping address.
3. The images shown are not the actual item and are for your reference only.
4. Fast shipping:All our packages use USPS First Class/UPS/Fedex.... Package Service
5. If you have not received your shipment within 15 days from payment , please contact us. We will track the shipment and get back to you as soon as possible with a reply. Our goal is customer satisfaction!
1. You have 30 days to contact us and 10 days to return it from the date it was received. If this item is in your possession more than 7 days, it is considered used and we will not issue you a refund or replacement. There are NO EXCEPTIONS!
2. All returned items must be in the original packaging and you must provide us with the shipping tracking number, specific reason for the return, and item custom lable.
3. We will refund your full winning bid amount, upon receipt of the item in its original condition and packaging with all components and accessories included, AFTER both Buyer and Seller cancel the transaction from eBay. OR, you may choose to have a replacement.
4. Return shipping is to be paid by the Buyer.
We maintain high standards of excellence (five stars review)and strive for 100% customer satisfaction! FEEDBACK IS VERY IMPORTANT TO US. We request that you contact us immediately BEFORE you give us neutral or negative feedback, so that we can satisfactorily address your concerns.
Copyright of Top-liftsupport. All rights reserved.