When you click on links to various merchants on this site and make a purchase, this can result in this site earning a commission. Affiliate programs and affiliations include, but are not limited to, the eBay Partner Network.
Price: $91.88
Compatible Vehicles:
- For Buick Riviera 1979-1985
- ForCadillac Eldorado 1979-1985
- ForCadillac XLR 2004-2009
- ForChevrolet Blazer 1987-2005
- ForChevrolet Camaro 1982-2002 (May not fit on front hub due to hub height issue)
- ForChevrolet Corvette 1984-2019
- ForChevrolet S10 1982-2004 (Does not fit front hub of 2WD Models)
- ForChevrolet S10 Blazer 1983-1994 (Does not fit front hub of 2WD Models)
- ForGMC Jimmy 1991-2005
- ForGMC S15 1982-1990
- ForGMC Sonoma 1991-2004 (Does not fit front hub of 2WD Models)
- ForPontiac Firebird 1982-2002 (May not fit on front hub due to hub height issue)
- ForPontiac Phoenix 1980-1984
- ForPontiac Trans Sport 1990-1997
--If you dont't know the specific of your vehicle, pls confrim by following the below steps:
1) Check Vehicle Bolt Pattern/ PCD
For 4-lug, 6-lug, 8-lug, measure the segment from the center of a bolt hole to the center of another hole.
5-lug is different, you need to measure the segment from the outermost point (not center point) of a bolt hole to the center of another hole.
Take 5 lug for example, if the length of segment as measured in the picture is 5.5"/ 127mm, and as these are 5 lugs, then the bolt pattern is 5.5"/ 127mm.
2) Check Vehicle Hub Bore Size
Measure the diameter of the center bore, make sure the spacer's diameter is the same as or greater than the axle diameter.
3) Check Vehicle Thread Pitch
There are different types of studs, sunch as M14X1.5, M12X1.5, 1/2"x20, 9/16"x18, please make sure the studs of wheel spacers is the same as the vehicle's, otherwise the spacer will not fit.
--Measure the fender gap to choose suitable thickness.
Line up a straight edge ruler against the siadewall of the tire, use the measure device to measure from the inside of the ruler to the inner fender lip.
Please take multiple measurements and use the smallest data point (The most closest spot may be at the front or rear edge of the fender). The maximum recommended spacer thickness= the smallest gap - 3/8"(10mm)
--Step for Installation Wheel Spacers
Item SpecificsManufacturer Part Number E819578WAYBrand EWAY-motorWheel bolt pattern 5x4.75" / 5x120.65mmVehicle bolt pattern 5x4.75" / 5x120.65mmLug Patterns 5LugsPackage Included 4 PcsColor SliverStuds M12x1.5Thickness 2" / 50mmWarranty 1 YearStud Grade 10.9Inner Diameter 70.5mmMaterial High Quality t6 6061 Billet AluminumSurface Finish CNC Machined Polished Aluminum FinishCondition NewShip from Ontario,CaliforniaCompatibility Fits Pontiac Chevrolet GMCHubcentirc YesPackage Weight 18.25lbOther Part Number 5 Lug-5x4.75-5x120.65-2 inch-CB 70.5mm-M12x1.5Interchange Part Number For Chevrolet Blazer Chevrolet S10 Camaro CorvetteSuperseded Part Number For GMC Jimmy GMC S15 GMC Sonoma Pontiac FirebirdTorqued Down By Hand At 70-80 FT/LBNote Some models will NOT fit Front Hub, Only Rear
Payment 1. Package handling takes about 1 business days at our warehouse, so please make sure entering correct payment and shipping information before checking out. Once your payment is completed, we are not going to accept any more changes to your order.2.All domestic orders will be shipped via DHL,USPS, UPS or Fedex from our US warehouse and usually arrives to your door in about 3-7 business days.3.Local pick up is not available.4.Orders Will be shipped out from our warehouse in US.5.International Buyers C Please Note:a. Import duties, taxes and charges are not included in the item price or shipping charges. These charges are the buyers responsibility.b. Please check with your country customs office to determine what these additional costs will be prior to bidding/buying.Warranty 1,We stand behind every product we sell.2,All of our brand new items come with a 60-Days money-back guarantee.3,We define the item as defective only if it doesn't function as described.4,It is the buyer's responsibility to understand the item description before bidding.5,We will replace the defective items, provided that they are in stock within the warranty period posted with the listing and the buyer return the original item and pay for the S&H cost for the replacement.6,We will refund the purchase price if the replacement is not available or buyer prefers a refund and send the original item back at his/her own cost.7,Shipping & handling cost are not refundable.8,Man-made damage by abuse or wrong operation is not covered by this warranty.9,No product liability insurance is assumed.Returns 1.All of our brand new items come with a 60-Days money-back guarantee.2.We define the item as defective only if it doesn't function as described, It is the buyer's responsibility to understand the item description before bidding.3.We will replace the defective items, provided that they are in stock within the warranty period posted with the listing and the buyer return the original item and pay for the S&H cost for the replacement.4.We will refund the purchase price if the replacement is not available or buyer prefers a refund and send the original item back at his/her own cost.5.Shipping& handling cost are not refundable.6.Man-made damage by abuse or wrong operation is not covered by this warranty.7.No product liability insurance is assumed.8.Refunds will be credited within 5 to 7 business days of receiving the return. When we've received and processed the return, we will refund the applicable amount minus any Recovery Fees (See Details Below) for the amount you paid for the item(s), plus any applicable sales tax.Payments
We only accept payment through PayPal. You can open a Paypal account at www.paypal.com.
Feedback 1. We will leave positive feedback once we get your payment.2. If you are dissatisfied for any reason, please do not be quick to leave negative/neutral feedback. We will work hard to make sure EVERY CUSTOMER 100% SATISFIED and resolve any problem for you and always leave positive feedback to all our customers.3. If you are satisfied with the product you received, please leave us positive feedback and 5 scores DSR. DESCRIPTIONPAYMENTSHIPPINGRETURN POLICYCONTACT US Shop CategoryStore Home wheel lug nut Leveling lift kit wheel hub bearing wheel spacers suspension kit brake pads Brake Rotor and Pads steering knuckle-7 Jake Stand Bed Step cargo cover ABS Wheel Sensor Steering Shaft hub caps OtherHot Item 4X 1.5\'\' 6x5.5 Wheel Spacer 12x1.5 Hubcentric For Toyota Tacoma 4Runner FJ Lexus USD 84.12 4x 2\" 8x170 Wheel Spacers 14x2 Studs Fits Ford F-250 F-350 Super Duty Excursion USD 129.68 (4) 4x156 2\" ATV Wheel Spacers 12x1.5 Fits Polaris RZR XP 1000 900 Trail Turbo USD 94.88 32X 14x1.5 Chrome 7 Spline Lug Nut + 2 Key For Ford F-250 Super Duty Ram 1500 USD 33.11 4Pcs 6x5.5 Wheel Spacers 3\" For GMC Sierra 1500 Chevrolet Silverado 1500 Tahoe USD 132.19 DeliveryNew List Item 2\" Front Steering Knuckle For Chevrolet Silverado GMC Sierra 1500 1999-2005 2006 USD 146.88 2 Front Wheel Hub Bearing Assembly For Nissan Cube 2009 2010 2011 2012 2013 2014 USD 70.52 Front Wheel Hub Bearing Assembly For Nissan Cube 2009 2010 2011 2012 2013 2014 USD 45.99 2 Rear Wheel Hub Bearing Assembly For Hyundai Elantra Veloster Kia Forte Forte5 USD 78.57 Front Wheel Hub Bearing For Ford Ranger Explorer Mazda B3000 B4000 Mercury 4WD USD 53.99 Help & InfoPayment PolicyShipping PolicyReturn PolicyFAQAbout Us (4) 2" 5x4.75 Wheel Spacers 12x1.5 For Chevrolet S10 Blazer GMC Sonoma S15 JimmyCompatible Vehicles:
- For Buick Riviera 1979-1985
- ForCadillac Eldorado 1979-1985
- ForCadillac XLR 2004-2009
- ForChevrolet Blazer 1987-2005
- ForChevrolet Camaro 1982-2002 (May not fit on front hub due to hub height issue)
- ForChevrolet Corvette 1984-2019
- ForChevrolet S10 1982-2004 (Does not fit front hub of 2WD Models)
- ForChevrolet S10 Blazer 1983-1994 (Does not fit front hub of 2WD Models)
- ForGMC Jimmy 1991-2005
- ForGMC S15 1982-1990
- ForGMC Sonoma 1991-2004 (Does not fit front hub of 2WD Models)
- ForPontiac Firebird 1982-2002 (May not fit on front hub due to hub height issue)
- ForPontiac Phoenix 1980-1984
- ForPontiac Trans Sport 1990-1997
--If you dont't know the specific of your vehicle, pls confrim by following the below steps:
1) Check Vehicle Bolt Pattern/ PCD
For 4-lug, 6-lug, 8-lug, measure the segment from the center of a bolt hole to the center of another hole.
5-lug is different, you need to measure the segment from the outermost point (not center point) of a bolt hole to the center of another hole.
Take 5 lug for example, if the length of segment as measured in the picture is 5.5"/ 127mm, and as these are 5 lugs, then the bolt pattern is 5.5"/ 127mm.
2) Check Vehicle Hub Bore Size
Measure the diameter of the center bore, make sure the spacer's diameter is the same as or greater than the axle diameter.
3) Check Vehicle Thread Pitch
There are different types of studs, sunch as M14X1.5, M12X1.5, 1/2"x20, 9/16"x18, please make sure the studs of wheel spacers is the same as the vehicle's, otherwise the spacer will not fit.
--Measure the fender gap to choose suitable thickness.
Line up a straight edge ruler against the siadewall of the tire, use the measure device to measure from the inside of the ruler to the inner fender lip.
Please take multiple measurements and use the smallest data point (The most closest spot may be at the front or rear edge of the fender). The maximum recommended spacer thickness= the smallest gap - 3/8"(10mm)
--Step for Installation Wheel Spacers
Item SpecificsManufacturer Part Number :E819578WAYBrand :EWAY-motorWheel bolt pattern :5x4.75" / 5x120.65mmVehicle bolt pattern :5x4.75" / 5x120.65mmLug Patterns :5LugsPackage Included :4 PcsColor :SliverStuds :M12x1.5Thickness :2" / 50mmWarranty :1 YearStud Grade :10.9Inner Diameter :70.5mmMaterial :High Quality t6 6061 Billet AluminumSurface Finish :CNC Machined Polished Aluminum FinishCondition :NewShip from :Ontario,CaliforniaCompatibility :Fits Pontiac Chevrolet GMCHubcentirc :YesPackage Weight :18.25lbOther Part Number :5 Lug-5x4.75-5x120.65-2 inch-CB 70.5mm-M12x1.5Interchange Part Number :For Chevrolet Blazer Chevrolet S10 Camaro CorvetteSuperseded Part Number :For GMC Jimmy GMC S15 GMC Sonoma Pontiac FirebirdTorqued Down By Hand At :70-80 FT/LBNote :Some models will NOT fit Front Hub, Only RearPaymentWarrantyReturnsPaymentsFeedback 1. Package handling takes about 1 business days at our warehouse, so please make sure entering correct payment and shipping information before checking out. Once your payment is completed, we are not going to accept any more changes to your order.2.All domestic orders will be shipped via DHL,USPS, UPS or Fedex from our US warehouse and usually arrives to your door in about 3-7 business days.3.Local pick up is not available.4.Orders Will be shipped out from our warehouse in US.5.International Buyers C Please Note:a. Import duties, taxes and charges are not included in the item price or shipping charges. These charges are the buyers responsibility.b. Please check with your country customs office to determine what these additional costs will be prior to bidding/buying. 1,We stand behind every product we sell.2,All of our brand new items come with a 60-Days money-back guarantee.3,We define the item as defective only if it doesn't function as described.4,It is the buyer's responsibility to understand the item description before bidding.5,We will replace the defective items, provided that they are in stock within the warranty period posted with the listing and the buyer return the original item and pay for the S&H cost for the replacement.6,We will refund the purchase price if the replacement is not available or buyer prefers a refund and send the original item back at his/her own cost.7,Shipping & handling cost are not refundable.8,Man-made damage by abuse or wrong operation is not covered by this warranty.9,No product liability insurance is assumed. 1.All of our brand new items come with a 60-Days money-back guarantee.2.We define the item as defective only if it doesn't function as described, It is the buyer's responsibility to understand the item description before bidding.3.We will replace the defective items, provided that they are in stock within the warranty period posted with the listing and the buyer return the original item and pay for the S&H cost for the replacement.4.We will refund the purchase price if the replacement is not available or buyer prefers a refund and send the original item back at his/her own cost.5.Shipping& handling cost are not refundable.6.Man-made damage by abuse or wrong operation is not covered by this warranty.7.No product liability insurance is assumed.8.Refunds will be credited within 5 to 7 business days of receiving the return. When we've received and processed the return, we will refund the applicable amount minus any Recovery Fees (See Details Below) for the amount you paid for the item(s), plus any applicable sales tax.
We only accept payment through PayPal. You can open a Paypal account at www.paypal.com.
1. We will leave positive feedback once we get your payment.2. If you are dissatisfied for any reason, please do not be quick to leave negative/neutral feedback. We will work hard to make sure EVERY CUSTOMER 100% SATISFIED and resolve any problem for you and always leave positive feedback to all our customers.3. If you are satisfied with the product you received, please leave us positive feedback and 5 scores DSR.All rights reserved.